Brand new Ecliptech Shift-I Progressive Shift Light. $80
Track – Street – Trials – Autocross – Circuit – Drift – Rally – Drag
“It’s worked brilliantly in my track car.
I’m pretty sure I’ve gained maybe ½ a second a lap from it, not to mention the benefit over a longer stint
due to a...
Brand new, never used SST Shift Light - Blue LEDs with Black Aluminum Tube
Product Description
SKU: A-146
Using Speedhut's patent-pending Smart-Shift Technology™, SST Shift-Light will maximize your shifting in every gear. The SST shift light captures up to 100 samples of each and...
Looking for part numbers on these. Using a phone so not easy to navigate the images on the normal parts websites. THought I'd ask here.
Need the rubber weatherstrip that goes on the inside of the door, it's the last thing you put back in when you remove the interior door trim. It has several...
Does anyone know if the Denso 471-1174 AC Compressor with clutch that's for 94+ will fit on my 1991 with the newer freon conversion already done?
Thanks!
Sent from my SM-G973U using Tapatalk
Selling my 2 AC Condenser Fans. I just took them off my 1991. I believe the part numbers are 80151-SL0-A01
The Driver side fan worked perfectly without any issues at all. So working great.
The Passenger side fan worked most of the time, but occasionally went out. If you hit it with a screw...
Due to my gauge mount where the center vents/clock normally is, most of the air from my AC is just blowing/disappating behind my center console area.
I just replaced my condenser motors and my AC is blowing cold. Based on another Prime member's suggestion, I want to block/tape off the entire...
I have the I's Impact Gauge mount above the center panel in my 1991 NSX. The air from my HVAC isn't blowing out too hard because I don't have the OEM DUct piece that connects it. My car had the NavPod when I bought it, but I switched to the I's impact because I wanted to use the gauges after I...
So I need to remove the center speaker from my rear interior part. I found some threads and also the instructions in the 1991 Servman Service Manual.
It says to "Remove 4 Screws"
Mine does not have 4 screws. THere's 4 holes, but no screws. My center panel is all black, including the plastic...
My drivier's side fan motor is going bad. Have to hit it to turn it on. Found some threads about it, but have a question about the part number.
Does anyone know if 80151-SL0-A01 is the same motor/part number for both sides?
Also, would anyone suggest if they would replace both sides since I'm...
I'm looking to buy an Oil Filter Wrench. I've found the OEM Part number 07AAA-PAAA100
Doing some looking on Amazon, Ebay, etc. Some have this listed as a "68MM Oil Filter Wrench" and some have it listed as a "65MM"
Does anyone know if it's a 68MM or 65MM for our cars?
I ask because I live in...
I'm trying to locate the part numbers for the AC/Heat Vents in the drivers door. By this I mean the point at which the air flows out of the door. There's 2 vents that the air flow direction can be adjusted. I need to replace one in my drivers side. Please see attached image. Sorry for the...
So my AC compressor is not working. I think it may be the relay or fuse. I haven't found it in the Service Manual.
Anyone know where/which relay and fuse I should check?
Any other suggestions?
Thanks,
I currently have 3 AEM Gauges in the center mount. What I don't like about my current gauge mount is it deleted the AC vents under there.
So, all of my AC is just blowing behind my dash and the air is wasting away.
I need to get my AC blowing in the car again.
I have 2 questions please.
1...
I need to get my ID2000 fuel injectors cleaned in my 1991 NSX. Yes they're huge injectors, but need them for my setup. They're basically new, but the car has not been started in 18 months due to a entire engine rebuild. I've been looking online and found INjector RX at www.injectorrx.com...
Hi fellow Primers,
I have a 1991 NSX and am having to replace the main engine bearings in my engine. I am running a Brian Crower 3.5L stroker kit and recently spun a bearing.
We had to have some slightly oversized custom pistons made, replace the crank shaft and also need new engine bearings...
Aloha Prime Family,
I need to replace all of the main engine bearings in my NSX except for the connecting rod bearings.
I know there's different colors and some colors take different amounts of bearings than others.
Can anyone please either
Provide me with a link that lists all of the main...
I have a 1991 800+whp NSX. When I had was ony 642whp, I snapped my driiveshaft in half shifting from first to second with drag radials on, which over revved engine and caused me to bend a valve spring. Since then, i have totally upgraded Turbo and all components inducing doing a Brian Crower 3.4...
Drivetrain advice, suggestions & experience from anyone 4 high powerd NSX for please
Aloha,
I have a 1991 NSX that made 674whp and 502wtq on 92 octane with a flex fuel system so I can run E100 ethanol, but had the chance to tune on ethanol, but should have been close to 800whp. My engine is...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.