I never had my car serviced at Crown. I used to use Ferman Acura when they had an NSX tech. The last time I used them, one of their techs destroyed the interior under the steering wheel and left it in my trunk. At least they replaced it at a cost of over $400. After that I used Nibal in Orlando...
I will second the above. I had to remove my Viper alarm system. It drove me crazy. I rebuilt my starter twice, replaced and or refurbished the ignition switch too many times to count only to find the problem was with the Viper. Once removed, not a single hiccup in starting the car. Jerry
I also have the HPS pads front and back on my 2000. No problems. I do most of my own work and don't remember anything special about switching out from stock to Hawk pads. Jerry
I have a BendPack 4 poster and a three air bag jack like the one mentioned above. The three bag lift is too tall in the relaxed position to fit under the NSX. The two bag jack looks like it will fit un Der the NSX. The three bag setup works well for my C-2 and C-3 vettes if I use the jack plate...
Mine was the opposite. Once the heat was on, it would not turn off. It turned out to be the control motor. I manually turned the valve to off as I am in Florida and don't use the heat. I did order a motor and got it from Japan after a six month wait. I have yet to install it. Good luck. Jerry
You mentioned that you found a Viper alarm in your car. I had one installed in my car for many years and it worked well until it did not. The alarm worked well but after a few years my car would not crank. I replaced the ignition switch a few times, cleaned and eventually replaced the starter. I...
When you settle down and are looking for a lift, come by my house for a look. I installed a Bend Pack four post lift in my garage years ago. I worked out all the challenges with space, power, air, garaged door etc. Jerry
While you are waiting for your ignition switch to arrive, consider removing your current switch and cleaning the contacts. I had the same problem you had and tried everything. I ended up removing my Viper alarm and all is well for a few years. Jerry
Sounds like you listed, but did not address the ignition switch. You can remove and carefully open it and clean the contacts. If they are burnt, the entire switch can be replaced for about $60. I had the same problem and chased it for some time. It turned out to be my aftermarket Viper alarm...
Thanks for the quick reply, that is the part I am referring to in my post. The cable connects to the mix manifold valve on the firewall. I think I can access it without dismantling much. I am worried that the mix valve on the firewall side where the other end of the cable is frozen. I don't...
Since winter is coming to Central Florida, on occasion I use my heater in the mornings. That said, when I cranked up the heat, it came on and would not shut down. The problem was diagnosed as a broken heater control. The cable was lifted on the blower motor and the valve was turned off to...
I have had great success with Mobil1 red synthetic grease. I used it on the bearings and slides in my Corvette door about 10 years ago. I had to take the door apart to fix a switch and found the grease was as new. I also use it in my tapered wheel bearings. I also used it on the shifter linkage...
Honcho: Thanks for your help. When you inquire at the site to confirm parts, you are informed that the part is discontinued. When I used the link you provided, the items were in stock and the order processed. I will post upon delivery of the part. I thought finding parts for my 60s Corvettes...
Does anyone know where to purchase a a pair of the relay rods mentioned above used to correct shaky headlights? All sources I have tried in America and Japan indicate permanently discontinued. Any help appreciated. Thanks. Jerry
Mike: I am glad it worked out well for you. Nice to know there are still a few people that can service the subassemblies of these cars. Regarding the new SOS clutch, give it some seat time. I think you will find that the touch is a bit different compared to the stock setup. I had mine changed...
Honcho: Thanks for the write up pictures. Looks like the parts listed in your photos will do both sides?? My buckets are shaking and I might as well order the parts now. Perhaps I will have them in the spring. Thanks. Jerry
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.