Search results

VIN # JH4NA1264MT001729 CURRENT MILAGE: 108,000 LOCATION: Lewisville TX ( suburb of Dallas ) PRICE: $27,500 FIRM NUMBER OF OWNERS: 2 CLEAN TITLE: yes ACCIDENTS: none PAINT & BODY WORK: small paint chip on hood, front bumper has typical tiny chips, Otherwise original perfect paint, wheels have...

18" staggered Mercedes rims with tires Set of 4 OEM seven spoke wheels, near perfect with tires, Front: 18 X 8.5 5 lug 112mm off set 28 with Dunlop 245 40 R18 Rear: 18 X 9.5 5 lug 112 mm off set 33 with Dunlop 275 35 R18 one very small scrape on one front rim otherwise they look and ride...

Two times I went through the exercize of trying to post some wheels for sale in the classified section and on both occasions it read submitting and nothing ever shows up !!! Is there a trick to this ? BTW the old classified section had so much more for sale, what happened to all that posting...

Here's what happens, air blows cold for about 20 min. then blower stops. turn car off for 15-20 Min and it starts up just fine. I removed the control unit and sent it to Brian to repair, installed and still doing the same thing, anybody have any ideas where the gremlin is?:confused:

Will that wrap work on the inside center console?

Air conditioning blowing strong when for no reason it stops blowing, and display goes blank. Nothing. Turn off ignition to check fuse, seems fine? Start up car and it works fine for about ten min. Then shuts down again, turn car off wait a bit start up and works again. Any Body have this happen...

What about changing it to a factory red interior, very few were made, but a striking combo IMO

Installing a B-Line air intake this weekend, Perfect timeto check hoses and clean TB, we'll see how it goes:smile:

Just noticed that the engine is pulsing about 500 rpm when at idle, 104,000 miles on car last changed plugs 15000! Any thoughts? Ed Resh

Turns out both fans were bad, I was able to replace both of them without having to evacuate the sealed system, everything is back to normal and it works better than ever, Didn't realize that asking some simple advise instead of doing a search was so irratiting to some people, and they just have...

Discovered that tapping on the motor will get it going cant live with that, both fans need to be replaced, is there a way to replace them without having to remove the entire condenser.? Really don't want to get into having to evacuate the system an recharge

The manual says to disconnect the 2-p connector to the condenser fan, but does not show where the connector is, can anyone shed some light on it's location?

Car cools fine when moving, stopped, cooling is diminished, checked the condenser fans neither were running, fuses and relay OK, need help from here guys

Always wanted a Black with red interior were they ever offered Pictures would be Great if it exists

Alright looked in the manual and saw that the OEM radio has two inputs, one that appears to accept a male plug for the mast antenna and another that is a female plug for the window glass antenna, like the the addapter pictured. Before I pull the radio out, I what to know if there are two oem...

I have a 91, are you saying there is a wire antenna built into the back hatch window, I can only see orange wires which I believe is a window defogger. Educate me, where is the plug located for the window antenna?

[/ATTACH] Just did this to my ride, Had Eurobotique in CA do the work, love the look.

Replacing front parking lights with LED's, and want them togo on with parking light switch, What fuse is for the parking lights the one that says ILLUMI LIGHTS or another one? Hope a photo is attached of the fuse in question !!!:

I found the information

Thanks, Lets hope it's unpluged.

Any reason why the lights on warning ding/ring would stop working all of a sudden? Where is the ringer, maybe wire came off?

Here is more contact information: Ed Resh 91 Berlina Black, black inside Lewisville Texas Office 972-221-8283 Cell 214 502 4658 e-mail [email protected]

Re: *** OFFICIAL DFW Member Roster **** I'm all for a tech session after the holidays

Do the screws come through the shaft far enough to allow the threads to be expanded or Crushed ? :confused:

Thanks for the walk thru, But until we figure how to fix with out just eliminating the thing I going to hold off, loctite has been ruled out along with JB weld, someone suggested RTV?? and welding the screws in place, welding scares me could cause the plates to warp, the weld could break off...