Search results

Check out this build: https://www.nsxprime.com/threads/just-another-j32-swap-6-speed.199833/ 3 mounts on the transmission. Not sure if you can reuse the NSX half shaft, but the driveaxles will need to be custom. Clutch cables from the TL is not going to work. The distance from the NSX...

Many issues with this retrofit. When done, you basically get a JDM 5 speed with a highway 6th turning around 2k rpm. Issues: 1) adapting the right clutch and flywheel 2) need to solution/figure out 3 of the 4 engine mounts 3) get longer shift cables and reroute them from front bottom to rear...

Is there a DIY on which parts to remove and which part to clean?

Another option is to use a forwarder (like Shippsy for GTA owners, or reship/shipito). You will need to pay for shipping twice and some service fees.

Is there a DIY available for shorting the wires?

So I finally took my car out for a lengthy drive. The steering wheel shake has been eliminated. Things I did over the winter: - changed all 4 wheel bearings - steering rack bushing - still using the same wheels and tires from before With the steering rack bushing in place however, the...

Chris, your videos made me go all out this winter. I’ve replaced all 4 wheel bearings, longer front wheel studs, steering rack bushing fix and more. Turns out one of my front wheel bearings had very minor play. Not sure if that was the culprit to my intermittent vibration. It’s still winter...

2000 is when they changed the LMA style. So a 98 still have the old style.

Fan control unit: http://www.nsxprime.com/forum/showthread.php/162741-Intermittent-Condenser-Fan-Mystery-I-ve-searched-(

I have LED reverse bulbs and taillight bulbs. I was thinking of getting LED brake/tail light bulbs, but was concerned about the “brake lamp” indicator on the dash. Similarly, not sure if LED signal bulbs cause hyper flash.

Just watched the video, the “knock bush” will eliminate that noise. I had a local company rebuild my steering rack and the noise came back after a year or so. So I hope Les’s bushing will be a more permanent fix. I *don’t think* it is related to the vibration, but I’m grasping at straws in...

I have been tracking down similar symptoms on my car, but with much more miles (150k+ miles) My observations: intermittent vibration. It comes and goes especially when going around a bend on the highway. I’ve done the following so far without success of eliminating the problem: 1) new...

Adding more info to the thread. There are different size bearings with the same 6203LLU part number. Be sure to get the 17mm inner bore, not 16mm, not 15.875mm...17mm

Thanks for the replies. Will check out and replace the idler pulley bearing and see if that does the trick. I do have intermittent alternator/charging issues, but it's been happening for so many years (http://www.nsxprime.com/forum/showthread.php/174671-Battery-Charging-Issue). If the idler...

Took the NSX out and noticed a whining noise from the engine at idle. Any ideals? Sent from my iPhone using Tapatalk

Finally getting around to do this mod...2 questions: 1) Does anyone have the wiring schematics for hooking up a 3 button AP2/RSX cruise control? 2) The NSX SRS wiring harness is pretty big. Where are good placements for them?

"Brake Lamp" Which LED 2057 bulbs are you guys using that are brighter and also produces the 2 stage brightness when pressing the brake?

As in this?

Just a thought, couldn’t you put the RHD driver piece on the LHD driver side but “inside out”? Not sure if the barriers are sided or not. Sent from my iPhone using Tapatalk

LHD vs RHD? Anyways, off topic question...which putty/gum did you use to secure the DIY poly sheet to the door?

It’s exactly that same as a 91 bumper, which you can download the service manual. In short, 6 bumper bracket bolts (14mm) near the middle. You will need to take off the bumper caps to access 2 of the bolts. Each side has 3 bolts/nuts (10mm) behind the fender liner. Sent from my iPhone using...

I didn't have a kiddie pool, so I used an ikea garbage pail. 1 bottle of dye per session. The pail wasn't deep enough, so I rolled up carpet (minus the padding at the back) and dunked one side at a time for 10 mins, then flipped. 40 mins total per session. After each session, I rinsed in...

Turned out very good, deep black, except for 1 issue....using hot water "shrinks" the carpet. Now my carpets are a bit off. If I were to do it again, I would use warm water, 3 bottles per side.

Don't think that is possible...

Yes, there is a knob at the bottom. Take off the clear cover and use a philips screwdriver to turn it. Sent from my iPhone using Tapatalk