Freshly built Toda Racing/RFY short engine for sale!!
Here we have my unused Toda and RFY Built engine (bottom end). All parts were sent to Toda where they cleaned, inspected and machined (bored, honed and decked) the block. They are so precise they measure the alignment of the journals and...
From my project car part out.
Pair of Comptech later Carb EO headers with test pipes. Will mate up to any standard (early type) exhaust/muffler
In very good condition with no dings or dents etc.. $1200 shipped from UK
Cedar Ridge Rear sway bar end links, Non compliance clamps, SoS Toe Links & Rear beam
From my unfinished track project Im parting out. Items less than 200 dry miles old unless specified
Cedar Ridge Rear sway bar end links, $150 shipped (from UK)...
I have for sale my AEM Infinity 8 from my unfinished Track project that Im parting out.
I bought it from SoS with their PnP harness.
It comes with everything as when new, but it used so the ancillary plugs have been pinned but I can supply the plugs with tails. Was fitted to my car for about...
Set of KW Clubsport coilovers from my track car project Im parting out.
Probably done 200 dry miles so like new.
These are a setup up from the V3s
$2450 plus shipping from the UK (approx $120)
$3500 new
SOLD
From my track car project. Complete AP BBK (front, rear and parking brake)
$3500 plus shipping from the UK - approx $150 with UPS
This is the AP Formula kit (all factory AP) for the NSX comprising ($8000 new)
6 pot AP fronts (CP5555) 38mm, 32mm, 28mm pistons)
4 pot AP rears (CP7622...
SOLD
For sale is a nearly new RFY Carbon intake - details here
http://www.rf-yamamoto.com/NSXengine/19.html
Fitted to my project track car. I had a trim a small piece off the black (non CF) piece to clear my roll cage but I have supplied a brand new upper carbon piece so you wont see this...
Change of plans means my BNIB! Fresh Science of Speed rebuilt C30 engine is for sale. Still in the crate in which it was delivered so zero miles. Basically had their full NA rebuild service with everything overhauled plus some extras.
Cost of just the rebuild was $8600 plus obviously I had to...
Im parting out a complete C32 engine - engine no. C32B1-3130064. I bought the engine as a 20k mile engine from a salvage/fire damaged car. It had been in storage for some time and some water had got into one of the bores. Unfortunately it looks like the corrosion has pitted the FRM liner and too...
I know we've already spoken but I'll state what I know to the best of my knowledge:1.
I dont think the 3.0 or 3.2 liners will be the issue with big boost, it will be pistons and rings which I think will be the same between the two. AMW In finland says you can run 450-500 on a low pressure 6psi...
WTB - I need a front bank cylinder head complete with cams. In good condition with no scoring on the journals. Could be bare but still need the cams.
Thanks
Mike
I bought a tired, but complete C30 engine and sent it to SoS for a rebuild. They stripped it down and one single head and single cam has scoring so needs replacing. Crank, rods, block etc. are all good for rebuild. NOTE - it is just the FRONT bank cylinder head and INTAKE camshaft that needs...
RFY (Racing Factory Yamamoto) GT Exhaust Version 1 with single tipsPretty much as new condition. Fitted to car and started but never seen the road.Comes with the noise restrictor. But unfortunately as its for my race car its too loud for some of the tracks I need to visit 95db)$2300 shipped to...
Ok folks, Im in the UK and want to use the ECU used by my tuner - OBR EFI Euro 4 - its a C30 on ITBs
There are no available base maps for this ECU so working from scratch
Ideally Id like a base map from something like an AEM V2 and we can pinch the sensor/coil and injector calibrations from...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.