will these wheels work???

[macspeed71107]

Front 18x8 +35
Rear 19x10 +24
Falken 452's 225x35x18 / 275x30x19

im thinking about buying these wheels from a nsx primer, my nsx is lowered all ready with neuspeed springs

 

[angus]

19x10 with a 275/30 is pretty maxxed out, but should fit without rubbing since you are lowered.

18x8 with a 35 WILL RUB EVERYWHERE with the 225/35/18 , I had a 18x8 36 offset and 225/35/18 452's (that's the tire that came on the rims) and it rubbed like crazy , killed my liners and even pulled my fender lip down once.

You'll need a 215/35 - and a narrow one at that .

 

[macspeed71107]

so if i go with a 215 35 18 on the front they may work? did u sell that turbo kit yet?

 

[angus]

The front will work with a 215/35 but will still be close so you may get occasional rubbing .

PM me about the kit!

 

[synth19]

The front will work with a 215/35 but will still be close so you may get occasional rubbing .

PM me about the kit!

I agree. I would definitely go with 215/35 and a tire brand that has a reputation for being narrow. Toyo? For comparison sake, I am running a similar offset, but you are extended 1mm further out more. I don't rub, but just barely. Worse case, you can run some slight negative camber in case you notice any rubbing.

 

[Hapa88]

The 18x8 +35 will fit but will probably rub. Falken 451s and the newer 452s run narrow, so those are the tires to use for the fitment. Also, as stated before, use a 215/35/18 tire.

19x10 +24 is pushing it.

Both picture below are lowered on Eibach Springs.

Below is a picture of 19x10 +35. (A +24 will stick out 11mm more)

And a 19x9.5 +23 (equivalent to a 19x10 +29). Your 19x10 +24 will stick out another 5mm from this)

 

[FogCityNSX]

I run 225/35/18 and 285/30/19. Fronts only rub at full lock against the fender liners like doing tight U turns or tight maneuvering like parking lots. Otherwise, it won't rub. I was even lowered 2-2.5" on coilovers with them before too.

18x8 40mm
19.9.5 40mm

Your rear rims will probably need to go narrower like 265. That's pretty far out!

 

[DragonBallZ.]

Hapa88,
Yea u will be pushing it..Yes i'm sure u can make it work, but to make it look good is another thing. I think u will need a little negative camber along with a stretch tire, other than that u will be poking out.

 

[angus]

I run 225/35/18 and 285/30/19. Fronts only rub at full lock against the fender liners like doing tight U turns or tight maneuvering like parking lots. Otherwise, it won't rub. I was even lowered 2-2.5" on coilovers with them before too.

18x8 40mm
19.9.5 40mm

Your rear rims will probably need to go narrower like 265. That's pretty far out!

You are using a 40 offset , the extra 5mm that the OP is considering will cause WAY more rubbing.

And the rear will have a bit of clearance still , I am running 19x10.5 with 22 offset and 285/30/19 PS2 and no rubbingt at all - buy only barely.

 

[angus]

The 18x8 +35 will fit but will probably rub. Falken 451s and the newer 452s run narrow, so those are the tires to use for the fitment. Also, as stated before, use a 215/35/18 tire.

Actually the 451's were narrow but the 452's are wider , I would look at hankook RS-2's if you can find them , or toyo t1r , even pirellis are narrow size for size.