Hi there,
For sale a great TAITEC C3 model 2 exhaust
extremely rare item
very light, around 19lbs. it is a single side exhaust
i think this is the lightest exhaust before TITAN one
in very good shape
http://www.gt-rom.net/gtrom/supertaitec/c3.htm
i sold the car with the original exhaust
it...
I will be able to seal the exhaust the first week of September. I will check fuel pressure too
If you have any more ideas until then, I am always listening.
yes i try to drive TCS turned off and it did not change a thing.
i am going to sealed my exhaust correctly first (i have a bad fuel smell in the cabine now and this more unbearable than the little hesitation....)
then i am going to check fuel pressure.
the reset i made was correct.
for the...
Can you watch the videos just to give me your opinion on the reading?
Now both bank read the same
I made a real reset ECU today, 5 hours without clock fuse then 12mn idling then driving the car for 15mn
for now no CEL codes are back
TCS codes are still there , I think they do not erase when...
so today i took time too get good read from my O2 sensors.
car ran for nearly 20mn before to be sure it was hot
here are the video from both sensor:
https://photos.app.goo.gl/inQeV5y1fgXFXBsL7
https://photos.app.goo.gl/oUiZPJkyGZfGwRqD7
voltage are constantly jumping from 0v to 1v on both...
Hi,
You are right, it was A26. There is a typo on the service manual it says A28 on the graph and A26 in the writing.
I used the service check connector yesterday but as I had made so much test disconnecting stuff , it triggered many things. today I am going to pull out the clock fuse and...
i performed some check on th O2 sensors.
found something strange:
first seems to be a problem with the heater from the back O2 sensors; i get 8 ohms between terminal C and D.
service manual tell me i need something between 10 to 20 ohms
i changed those O2 sensor 6 month ago with denso one (not...
I will work again on the car tomorrow.
when i unplug the O2 sensor the car runs as bad as before. we can conclude that unplugging the O2 sensor do not trigger the same fail safe mode as unplugging the TPS. and i think if unpluging the TPS was acting on close or open loop, unplugging O2 sensor...
Hi,
It is to late today for me to test the O2 voltage. Moving out the ECU to test there is a little pain in the a..
But i drove the car traction control Turned off TPS pluged in and the issue was still there.
I ll try to check for O2 voltage this week
Thanks again
Hi guys
news are not so good actually
today i worked on this and it turned out to be more and more confusing
- test TPS AT THE ECU, got VCC 5V , min 0,53 max 4,37V, very linear all across no peak at all (i have a video to confirm)
- Test second TPS (under the trottle body, for TCS use i think)...
Men!!! you are great
i do not understand everything precisely but both of you had just the same understanding of the thing as i was.
i think my problem as been narrowed to the TPS because when i unplug it the car runs fine. if i had an injector clogged it will be clogged even when i unplug the...
Hi, i will change the TPS with the second one i bought and check voltage at the ECU connection just to be sure then i will check the wiring and the plug.
then i come back to you guys
if my problem can only come from the TPS it will be easier for sure
thanks A LOT for your help
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.